[РЕШЕНО] Помогите с Twonky

****************************
* TwonkyServer Linux HowTo *
****************************
This document was last modified June 16th, 2015.

The Twonky UPnP server for Linux is available for different
machine architectures:

- Standard PC (x86)
- ARM (Advanced Risc Machine) big and little endian
- MIPS (Microprocessor without interlocked pipeline stages)
big and little endian
- PowerPC (Performance optimization with enhanced RISC Performance Chip)
- SH3 (Hitachi SH)
- SH4 (Hitachi SH)
- SPARC (Scalable Processor ARChitecture)

*****************
* Package Content

Your package will consist of the following files:

twonkystarter Twonky UPnP server starter
twonkyserver Twonky UPnP server
cgi-bin/* cgi scripts for twonky
plugins/* plugins for twonky
resources/* resources for twonky
radio.m3u Sample playlist
Linux-HowTo.txt This file
NOTICES-Server.txt Licenses and notices for open source used for Twonky Server
TwonkyServer-Readme.html Release notes
Terms of Use*.pdf Licence Agreement
twonky.license/twonky.dat License file required to run Twonky Server
twonky.sh Sample autostart script
twonkyserver-default.ini Default configuration for Twonky Server

*********
* Install

Copy all files (keeping the directory structure) into your most
favourite installation directory, e.g. /usr/local/twonky.

Make sure that the server file, plugins and the cgi scripts have the exe bit set.
If not, try:
"chmod 700 twonkys* twonkyproxy cgi-bin/* plugins/*"

Twonky needs an "appdata" folder to store its database and other runtime generated
files. The default location for this depends on the user running the server. For
the user root (id = 0) this is
/var/twonky

For all other users this is
$HOME/.twonky

To specify an alternate location for the "appdata" use the command line switch
-appdata "/<PATH TO APPDATA FOLDER>"

The specified path needs to be full qualified, do not use relative paths here.

In any case make sure that this folder exists and is writable before starting the
server.

Now start the server with a full qualified path (never just "./twonkystarter"),
but "/usr/local/twonky/twonkystarter" . The server will display a startup
message. The server is running now and you can find and use it with
your UPnP client device. Before you continue, you should point the
server to one or more content directories via the configuration
web-page.

To open the server's configuration web-page, open the following url in a web
browser:
http://127.0.0.1:9000/webconfig

If the server can not be found by any client device check your
network firewall settings (see below).

To enable autostart of the server, you need to be a Linux expert,
because all Linux flavours differ and no general procedure can be
suggested. In many cases "twonky.sh" could be adapted to your
needs and linked into an appropriate location to enable autostart.
The script is intended to work on SUSE, OpenSUSE, Fedora Core and other
Linux Standard Base (LSB) compliant systems when installed into
/etc/init.d and linked to rc3.d and rc5.d as S99twonkyserver and
K99twonkyserver:
"ln s ../twonky.sh S99twonkyserver"
"ln s ../twonky.sh K99twonkyserver"

The installer script (twonky*.sh) is not working for modern ubuntu linux
systems due to incompatibitlities with some system config tools (chkconfig
vs. update-rc.d). The manual installation however is unaffected.

*********
* Network

Eventually it is necessary to have a multicast route set for the
server by issuinge, e.g.:
"route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0"

If Iptables is enabled on the linux system, some rules shall be added for Twonkyserver
A standard configuration would be the following.
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
target prot opt in out source destination
ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0
ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED
ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:1900 # BYEBYE/ALIVE MESSAGES
ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:1030 # MSEARCH
ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:9000 # TwonkyServer WebUI
ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:5353 # Airplay discovery (mDNS) - polling to multicast
ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp spt:5353 # Airplay discovery (mDNS) - answers from client
ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:443 # https
DROP all -- * * 0.0.0.0/0 0.0.0.0/0

***************
* 64bits Debian

If you are running a Debian distribution on a 64 bit architecture, it
is possible that you need to install the 32 bit compatibility
libraries. In this case invoke:
"apt-get install ia32-libs"

Contact
-------
Website: http://www.twonky.com
mailto: support@twonky.com